Custom wardrobe installation manual
[ Chinese wardrobe network ] First, the installation preparation:
1. Determine the installation task. Prepare the installation tool.
2. Contact the customer: Proactively contact the customer before the task is shipped, initially determine the time to arrive at the customer's home, and let the customer prepare for the work; for various reasons (vehicle traffic on the road or unfamiliar with the road) failed to reach the customer's home according to the scheduled time. At the time, the installer should notify the customer in a timely manner and explain the reason and estimated time of arrival.
Second, the installation method:
1. Determine the installation location according to the drawings. If there are a few cabinets put together, ask the customer room number first, and sort the plates according to the room number.
2. Check the hardware of the checklist, whether the number of cabinet parts matches the number of packages of the package details, and then check whether the glass, the door is cracked, whether the door is scratched, and report the department manager immediately if there is any abnormality. Custom furniture, custom furniture.
3. Unpacking: First unpack all the side panels, top and bottom layers, check whether the panels are stenciled, spread the wrapping paper on the ground to prevent the floor from squashing the panels, and then apply the rubber pellets. Connect the screws, the wooden plugs on the top and bottom plates, the large cakes, and gently place them against the wall in order, and stack all the excess wrapping paper in the appropriate place.
4. If there is a difference between the upper and lower cabinets, first install the lower cabinet and then install the cabinet. When the space is large, use horizontal installation. If the space is not large enough, use vertical installation.
5. Installation rejection: If there are plaster lines on both sides of the wall, you can leave 40mm in front of the two sides of the board, and insert the top part of the top cabinet under the plaster line, and then align the side with the plaster line. .
6. For the installation of the side panels to the top, first place the high side panels in a parallel thrust installation position of 600 mm to determine whether the height is appropriate. A 3-5 mm gap is required between the high side panel and the ceiling. Custom furniture, custom furniture.
7. Installation example of standard 2+4+3 combination:
7.1. The cabinet side panel is laid flat on the ground. First, fill the rubber pellets and fix the three-in-one linkage.
7.2. The laminate is set with the connecting rod and the large cake.
7.3. The solid layer is flattened, the three-in-one cake of the skirt line faces downward, the solid layer cake at 2100mm faces upward, and the other large cake holes face downward.
7.4. Nail the backboard.
7.5. Installation of Cabinet 3 is the same as Cabinet 2.
7.6. The No. 2 cabinet and the No. 3 cabinet are erected inward, so that the top floor of the No. 4 cabinet is aligned with the three-in-one hole of the No. 2 cabinet and the No. 3 cabinet, and the large cake is tightened, and the No. 4 cabinet has a 20 mm inside the back line. Fixed with the foot code.
7.7. Nail the backboard.
7.8. Push the installed cabinet to the position you want to install.
7.9. Close the position according to the situation on the spot.
8. Installation in the cabinet:
8.1. The living layer is mainly divided into equal parts, and the space can be arbitrarily selected. After the layer of slabs is installed, the living layer is placed.
8.2. If there are multiple drawers in the cabinet, they can be installed from the bottom, and finally the corners are fixed with a corner. Each drawer has a spacing of 2mm.
8.3. If there are three kinds of accessories, such as drawers, pants racks and lattice racks in the cabinet, first install the drawers, then install the grid racks, and finally install the pants racks. The distance between the three fittings is 20mm.
8.4. The L frame can be installed after the back plate is nailed, and is fixed on the back plate by the corner code on the inner side of the L frame.
9. Installation of three sections of rails:
9.1. First install the rails on the side panels of the drawer so that the edges of the rails are flush with the edges of the side panels of the drawers. Move the rails up and down as needed to the appropriate position. The front end is close to the back of the drawer panel and fixed with screws.
9.2. Then install the rail casing on the positioning hole of the side plate, and move it up and down as needed, until it is in the proper position, and tighten it with screws on the fixing hole.
9.3. The edge of the rail is 23mm away from the corresponding fixed layer, and the front end of the rail is 20mm away from the front edge of the side panel.
9.4. When there are many drawers, the rail housing can be installed from bottom to top. The distance between adjacent rails depends on the size of the drawer.
10. Installation method of clothing Tongtuo:
The intersection of 35mm from the top plate and 240mm from the back plate is the upper face of the clothing pass, so that the second hole screw is fixed after the clothes are placed vertically.
11. Tuen Mun installation:
11.1. The upper and lower rails should be installed in a balanced, stable, self-tapping screw.
11.2. Disassemble the paper from the door and put it into the upper and lower rails to adjust the bottom wheel to make it slide freely when the door is pushed and pulled.
11.3. Install the positioning piece, dustproof strip and anti-collision strip in place.
Third, the installation notes:
1. Check the work before installation, find the abnormality, and feedback in the first time to make corrections in time.
2. Carefully check the matching of the drawing identification with the site to determine the installation sequence.
3. Pay attention to the protection of the product assembly during the installation process.
4. Beam position, top line, and cut-off angle of the closing plate should be carefully checked and cut accurately.
5. Note that the hole surface of the side panel of the No. 4 cabinet should not be placed in the No. 4 cabinet.
6. When the nail backing plate is used, the diagonal of the measuring cabinet should be equal. If the solid layer is uneven, it should be flattened with a planing knife to nail the backing plate.
7. If the customer asks a question during the installation, it should be answered in time and the rationality of the disposal method should be informed.
8. If there is a problem with the installation, the installation worker must return to the installation note and return to the repair order to complete the tracking service.
9. After installation, you must first self-check, adjust, and then the customer acceptance, signature confirmation.
10. The customer must have a clean environment after the completion of the installation service process.
Fourth, the solution of difficult problems:
1. The cloakroom or installation space is small, and it must be handled by special methods during installation.
1.1. If the cloakroom is high, install it from the inside out.
1.2. There is a top cabinet, the outside of the cabinet, the lower cabinet and the upper cabinet are installed at the same time and then the lower cabinet is installed.
1.3. Adopt vertical loading method, first and then outside, from left to right and from right to left, the side panels are first connected to the main line, and the bottom line is fixed by the corner code. After the board, people have to climb out from the top cabinet. If the space in the top cabinet is too small, you can saw the back panel behind the drawer and then fix the back panel with the corner code.
2. There is an electric socket in the cabinet at the scene, which can be opened by the measuring ruler. The opening of the electric plug board is subject to the wall of the cabinet. If necessary, the electrical board can be mounted on the back panel without opening.
3. The solution for the top cabinet and beam cutting angle: first install the lower cabinet, saw the top cabinet board into the corresponding height, and place it on the side panel of the lower cabinet to take the spot ink as the standard sawing angle.
4. The solution for the uneven connection between the two closing plates and the top line. When making the first closing plate or the top line and adding a small board to the interface of the other board, expose 100-200mm, the purpose is to locate the board which is connected with it, and the small board can be fixed with 502 glue or screw.
5. Analysis and solutions to problems when installing drawers:
5.1. When the drawer is installed, the drawer plate and the side plate are often not straight, and the gap is quite different. The reasons are as follows:
5.1.1. The cabinet body is inclined.
5.1.2. The dotted line marked is not at right angles to the side panels.
5.1.3. The installation rail is not parallel to the dotted line.
5.1.4. The distance between the fixed layer and the dotted line is not accurate enough.
5.1.5. The three-in-one position of the drawer is not accurate enough.
5.1.6. The dotted lines on both sides are not at the same level. Note: Dotted line refers to the line of the installation size indicated by the pencil during installation.
5.2. The reasons why drawer activities are not smooth are:
5.2.1. The interior of the cabinet is not standard.
5.2.2. The drawers are not standard, including the size of the bottom plate, the size of the plate after the pumping, and the deviation of the three-in-one hole position.
5.2.3. The quality of the track is not good, such as insufficient lubrication, metal burrs on the movable contact surface, deformation of movable parts, etc.
5.3. The solutions to the above problems are:
5.3.1. If the drawer is loose and tight inside, the situation usually occurs when the nail back plate is not noticed, so that the side plate is deformed, and a hammer pad can be knocked out on the inner side of the side plate to restore the original shape.
5.3.2. The plate after the pumping or the side plate is too large to be small or small.
5.3.3. Carefully check the quality of the track and replace it if there is a problem.
6. After the door is installed, there is a very loud or difficult solution:
6.1. The reason for the abnormal sound:
6.1.1 The frame is in contact with the upper rail for friction.
6.1.2 The bottom wheel box is in contact with the lower rail for friction.
6.1.3 The bottom wheel and adjustable parts are loose.
6.1.4 The bottom wheel is deformed or has a raised portion.
6.1.5 Top wheel deformation.
6.2. The solutions to the sound are:
6.2.1. Increase the distance between the bottom wheel and the lower rail.
6.2.2. The raised portion of the bottom wheel can be disposed of.
6.2.3. The deformed top and bottom wheels are replaced.
6.2.4. Use screws to fix the upper and lower rails.
6.2.5. When installing the lower rail, place a piece of paper that is the same width under the lower rail.
6.3. The main reason for the difficulty of pushing is that the position of the upper and lower rails is incorrect or not matched, and the quality of the bottom wheel is not good or the space is too small.
6.4. Solution:
6.4.1. The space of the door is reserved and the diagonal is equal.
6.4.2. The position of the upper and lower rails should be symmetrical, especially if the lower rail is straight.
6.4.3. Carefully check the quality of the bottom wheel.
7. When the wall- mounted wardrobe cabinet is larger than the actual size, the cabinet No. 4 can be changed to a small size.
8. When the gap between the door and the card door is large, there may be a deformation of the frame. The inner and outer doors can be interchanged, and then the dust bar is added at the intersection of the two doors of the upper rail. If it is a full wooden door, The frame can be pressed down.
9. When the clothing is more than two cabinets on the upper cabinet, the top and bottom panels are easy to be confused: because the cabinets on the closet are made of different sizes, the top and bottom panels are not the same size, and the two sides are not the same width as the middle.
10. Deformation of the side panel of the closet: mainly the side panel of the closet is placed below the 2100mm of the light surface, and the fixed layer is placed. The side panel is in an empty state, and the door and the side panel are not tight. In the design, put a solid layer below 2100mm of the light side panel.
There are different cover materials for 3+2+1 Manual Recliner Sofa, you can choose the material you like. We have leather 3+2+1 manual recliner sofa, fabric 3+2+1 manual recliner sofa and PU 3+2+1 manual recliner sofa. And you can have different functions for your 3+2+1 manual recliner sofa. You can choose manual recliner sofa, power recliner, loud speaker, USB charging, LED light and cupholder, etc. The full set of the 3+2+1 manual recliner sofa includes one single recliner sofa, one loveseats recliner sofa and one 3 seats recliner sofa. You can choose the one which suitable for you.
3+2+1 Manual Recliner Sofa,Sofa Reclinable,Living Room Furniture Sofas,Living Room Sofas Sets
Kaifeng Lanwei Smart Home Co., Ltd , https://www.sofawickles.com