Screen 5055 common fault
Fault one: suddenly initialized or initialized
Treatment method:
1 It is possible for the PSI power supply to pressurize and measure whether the DC voltage of the MCON board TP-AC and TB6 is in the range of 4.8-5.3V. If not, adjust the VRI of the PSI board.
2 Possible motherboard failure (MCON board), check each motor, insurance.
Fault 2: Report "Machine eror15" error
Treatment method:
1 check the laser head: in the dark room to observe the light path whether there is light (usually) high DPI (3000,2400) output only after a brief period of light error, with a low DPI (1000,2000) can output about A4 format image after the light disappears and error . This is usually a laser head failure.
2 Check the Star sensor if there is light in the optical path and report an error. Check if the "Star sensor" sensor is in the wrong position or if it is dirty.
3MACON board is bad.
Fault 3: Image Distortion
Treatment method:
1 The five-sided mirror is unstable and has jumps.
2 Unstable sheets: parts are not in place when installed, and parts are worn over time.
3TIF graphics exceed 100m.
Fault 4: Report "Machine error 17,18,19 or Load error" error
Treatment method:
1 check the motor (Front slack guide motor).
2 Check the status of the "Front slack roller position" sensor to see if it is in the wrong position.
Fault 5: Black line (direction is horizontal)
Treatment method:
1 Because the roller is dirty, clean the roller.
2 The ground wire is not good and the roller is static.
3 The operating voltage is unstable There is a large voltage difference jump.
4 The data transmission is unstable (the RIP machine's memory, dispatch card, and hard disk will all have an impact).
Failure six: 5055S machine report (Film jam 5) wrong
Treatment method:
1 The cassette was turned over. Filming couldn't get in. When it was put into the cassette, the machine began to rotate. If it was finally heard, the machine must be a card to adjust the position of the aluminum sheet on the right side of the cassette.
2 Deformed cassette holder.
3 machines are not horizontal
Fault seven: 5055 reported "Film jam 4" wrong
Treatment method:
1 machine is not level.
2 Film is not good.
Fault 8: Film has a white stripe (softer)
Treatment method:
1 The compensation mirror has dirty spots.
2Shuter has dirty things.
Fault 9: The machine has a white film, it is re-emerged and disappears, the word has a ghost image, and the image shifts.
Solution: Replace the B9110 chip on the motherboard.
Fault 10: Display Alarm: SERIAL ERROR 11
Cause: It should be a communication error between the imagesetter and the puncher.
deal with:
1 Check if there is any problem with connection, power (ground, voltage).
2 Disconnect the imagesetter from the punch (set the DIPSW switch 6 on the main control board to ON) and try it out separately. If the error is still reported, the motherboard may be damaged.
Fault 11: Display alarm: MACHINE ERROR 30
Cause: It should be caused by the motherboard power supply lower than 4.8V.
Phenomenon: RECORDING 1%-100% suddenly disappear when you are filming, reinitialize INSTALLING...
Treatment: Use a voltmeter (DC) on the main control board to measure the voltage between TP06--TPA02 to see if it is less than 4.8V (normally 4.8V-5.3V). If so, adjust the PS1 (a small screw on the blue-yellow head, turn clockwise, and increase the voltage) on the power board to make the main board voltage 5V. If not, consider replacing the power board.
Fault 12: Display alarm: MACHINE ERROR 24
Cause: The gear between the imagesetter and the take-up box is not well-matched or the sensor is out of order.
Remedy: 1 Readjust the position of the pack. (guide)
2 Replace the sensor.
Fault 13: Display Alarm: AFP POWER OFF 1
the reason:
1 only activated the imagesetter and the punch did not open. (guide)
2 The sockets of the sockets OF111 and OF112 on the mainboard are inserted in reverse.
3 The connection on the motherboard is loose.
Fault 14: Display Alarm: LOADING ERROR
Cause: An error occurred during the loading process.
Treatment: 1 When the film is placed on the roller to the appropriate position. (guide)
2 Check that the connection between the main motor and the main roller is operating normally.
Fault 15: Display Alarm: WIDTH NOT ENOUGH
Cause: The film width does not match the setting width of the imagesetter.
Treatment: Set up to 549.9mm in the imagesetter. Change the settings in the FILM menu. (guide)
Fault 16: Monitor Alarm: MACHINE ERROR 2
Cause: The front cutter has failed
deal with:
1 Is the plug position on the ON 110? (After the mainboard is replaced by a newly installed or old machine).
2 Check that the cutter's fuse is ON or OFF and should be ON.
3 The position of the knife sensor moves or the sensor is broken.
Fault 17: Display Alarm: MACHINE ERROR 15(12)
Cause: When the exposure was started, the exposure signal was too weak or the sensor did not sense the light signal.
deal with:
1 Adjust the light value, clean the light path, and clean the sensor. (guide)
The 2 line head sensor position moves.
3 motherboard bad or bad laser.
Fault 18: Display Alarm: IMAGE ERROR
Cause: Data signal transmission communication error.
deal with:
1 Check that the SCSI interface and interface board are properly in place.
2 Format the hard disk (for customers using the hard disk).
3 Replace the new hard disk (for customers using the hard disk).
Trouble 19: There are black lines on the film from the imagesetter (very thin black lines, along the direction of the sheet), one or more.
   the reason:
1 static electricity
2 The film was scratched before it entered the fixer during film removal.
deal with:
1 Check whether the ground wire meets the requirements and whether there is loose contact. Measure zero voltage (less than 3V required).
2 Clean the exit of the control machine and clean the inlet position of the punch machine. The treatment is to use advanced lens paper or suede wipes with alcohol.
3 Developing, fixing, and washing rollers of the hedging machine. Be careful not to scratch the underlying rubber roller.
Punching machine section
Fault 1: The punching machine starts up and the developing lamp starts to light up
Treatment method:
1 Dirty spots at the sensor block the light and be careful to clean it with a clean cloth or cotton.
2 sensor is broken.
Fault 2: There are many white spots in the field
Treatment method: Fix the mixed development, change the liquid.
Failure three: boot report "card"
Treatment method:
1If there is a stuck film, the motor will not turn.
2 Check if the motor has voltage and voltage, and the motor will not turn bad for the motor.
3 If the motor does not reach the voltage, the motherboard is faulty.
Fault 4: The drying part has water or the fixing is easily mixed in the developing
Treatment method: Drainage level higher than the water level.
Fault 5: There are black lines on the film (marked bruises with multiple fixed positions)
Cause: The film was bruised before entering the fixer during film removal.
deal with:
1Check whether the gear position of the middle group of punching machine moves or loses the gear position.
2 Developing, fixing, washing roller cleaning of the hedging machine. Be careful not to scratch the underlying rubber roller. Note: Determine if the line is caused by the punch or the photo machine.
1, manual punching.
2. Different positions for punching.
3, the film back in red.
Fault 6: There is a white line on the film
Cause: The film was scratched.
Processing: Developing, fixing, washing roller cleaning of the hedging machine. Be careful not to scratch the underlying rubber roller.
RIP, output section
Fault 1: Cannot make output or cannot explain large files
   Treatment method:
1 The machine memory is small.
2 RIP print buffer setting is too small, 16384MB should be set.
3 RIP software allocates small memory (preferably 256 or more).
Failure 2: The gradient effect of Illustrator's launch is poor
Treatment method:
1 Select [Setup] in Illustrator's [File] menu, and then select [Compalible Gradient and Gradient Mesh Printing].
Fault 3: HQ-510 can be issued, Founder PSP can not be issued
Solution: NT operating system problems, re-install NT after formatting the hard disk
Artificial Grass Ball,Artificial Topiary Trees ,Artificial Hanging Balls ,Artificial Topiary Balls
Flower, Bonsai & Decorative Plant Co., Ltd. , http://www.nbartificialbonsai.com