The company specializes in supplying Elisa kits, quality assurance, price concessions, and can provide free testing services, please call to consult!

Human adiponectin (ADP) enzyme-linked immunoassay (ELISA)

Kit instruction manual

This reagent is for research use only

Purpose: This kit is used to determine the content of adiponectin (ADP) in human serum, plasma and related liquid samples.

Kit composition:

Kit composition

48 hole configuration

96-well configuration

save

Instructions

1 serving

1 serving

Sealing film

2 pieces (48)

2 pieces (96)

sealed bag

1

1

Enzyme coated plate

1 × 48

1 × 96

Store at 2-8 ℃

Standard product: 2700ng / L

0.5ml × 1 bottle

0.5ml × 1 bottle

Store at 2-8 ℃

Standard dilution

1.5ml × 1 bottle

1.5ml × 1 bottle

Store at 2-8 ℃

Enzyme reagent

3 ml × 1 bottle

6 ml × 1 bottle

Store at 2-8 ℃

Sample diluent

3 ml × 1 bottle

6 ml × 1 bottle

Store at 2-8 ℃

Developer A liquid

3 ml × 1 bottle

6 ml × 1 bottle

Store at 2-8 ℃

Developer B liquid

3 ml × 1 bottle

6 ml × 1 bottle

Store at 2-8 ℃

Stop solution

3ml × 1 bottle

6ml × 1 bottle

Store at 2-8 ℃

Concentrated washing liquid

(20ml × 20 times) × 1 bottle

(20ml × 30 times) × 1 bottle

Store at 2-8 ℃

Experimental principle:

This kit uses the double antibody sandwich method to determine the level of human adiponectin (ADP) in the specimen. A microplate was coated with purified human adiponectin (ADP) antibody to make a solid phase antibody. Adiponectin (ADP) was added to the monoclonal antibody-coated microwells in turn, followed by HRP labeled adiponectin (ADP ) The antibody binds to form an antibody-antigen-enzyme-labeled antibody complex. After thorough washing, the substrate TMB is added for color development. TMB is converted into blue under the catalysis of HRP enzyme, and into the final yellow under the action of acid. The color depth is positively correlated with adiponectin (ADP) in the sample. The absorbance (OD value) was measured with a microplate reader at a wavelength of 450 nm, and the concentration of human adiponectin (ADP) in the sample was calculated by a standard curve.

Sample processing and requirements:

1. Serum: room temperature blood coagulates naturally for 10-20 minutes, centrifuged for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully and centrifuge again if a precipitate appears during storage.

2. Plasma: EDTA or sodium citrate should be selected as the anticoagulant according to the requirements of the specimen, mixed for 10-20 minutes, and centrifuged for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, it should be centrifuged again.

3. Urine: collected in a sterile tube and centrifuged for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, centrifuge again. Pleural and ascites, cerebrospinal fluid reference implementation.

4. Cell culture supernatant: When detecting secreted components, collect with a sterile tube. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. When detecting the components inside the cells, dilute the cell suspension with PBS (PH7.2-7.4), and the cell concentration will reach about 1 million / ml. Through repeated freezing and thawing, the cells are destroyed and the intracellular components are released. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, it should be centrifuged again.

5. Organize the specimen: after cutting the specimen, weigh it. Add a certain amount of PBS, PH7.4. Quickly freeze and save with liquid nitrogen for later use. After the specimen melts, it still maintains a temperature of 2-8 ° C. Add a certain amount of PBS (PH7.4) and homogenize the specimen with a manual or homogenizer. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. After aliquoting, a portion is to be tested, and the rest is frozen for future use.

6. The specimen should be extracted as soon as possible after collection. The extraction should be carried out according to relevant literature. If the test cannot be performed immediately, the specimen can be stored at -20 ℃, but repeated freezing and thawing should be avoided.

7. The sample containing NaN3 cannot be detected because NaN3 inhibits the activity of horseradish peroxidase (HRP).

Steps

1. Dilution and loading of standard products: set 10 standard wells on the enzyme-coated plate, add 100 μl of the standard products in the first and second wells, and then add the standard products in the first and second wells. 50μl of diluent, mix well; then take 100μl from the first well and the second well and add them to the third and fourth wells respectively, and then add 50μl of standard diluent to the third and fourth wells respectively, mix well; Then take 50μl each in the third and fourth wells and discard it, then add 50μl each to the fifth and sixth wells, and then add 50ul of the standard dilution solution to the fifth and sixth wells respectively, and mix well; After mixing, take 50μl from the fifth and sixth wells and add them to the seventh and eighth wells respectively. Then add 50μl of the standard dilution solution to the seventh and eighth wells respectively. Take 50μl from the eight wells and add them to the ninth and tenth wells. Then add 50μl of the standard dilution solution to the ninth and tenth wells. After mixing, take 50μl from the ninth and tenth wells and discard. (After dilution, the volume of each well is 50μl, and the concentration is 1800ng / L, 1200ng / L, 600ng / L, 300ng / L, 150ng / L)

2. Add samples: set up blank wells (the blank control wells do not add samples and enzyme reagents, the rest of the steps are the same) and the sample wells to be tested. Add 40μl of sample diluent to the test sample well of the enzyme-coated plate, and then add 10μl of the test sample (the final dilution of the sample is 5 times). Add the sample and add the sample to the bottom of the well of the microplate, try not to touch the wall of the well, shake gently to mix.

3. Incubation: Seal the plate with a sealing plate and incubate at 37 ° C for 30 minutes.

4. Mixing solution: Dilute 30 times (20 times of 48T) concentrated washing liquid with distilled water 30 times (20 times of 48T) and then use.

5. Washing: Carefully peel off the sealing film, discard the liquid, spin dry, fill each well with the washing liquid, let it stand for 30 seconds and then discard, repeat 5 times and pat dry.

6. Add enzyme: add 50μl of enzyme label reagent to each well, except blank well.

7. Incubation: The operation is the same as 3.

8. Washing: The operation is the same as 5.

9. Color development: add 50μl of developer A to each well, then add 50μl of developer B, mix gently, and develop at 37 ° C in the dark for 15 minutes.

10. Termination: Add 50μl of stop solution to each well to stop the reaction (at this time the blue will turn to yellow).

11. Determination: Measure the absorbance (OD value) of each well in sequence with the blank air conditioner at zero and 450 nm wavelength. The measurement should be carried out within 15 minutes after adding the stop solution.

Precautions:

1. The kit should be equilibrated at room temperature for 15-30 minutes before being taken out of the refrigerated environment. If the enzyme label coated plate is unopened, the strip should be stored in a sealed bag.

2. Crystals may be precipitated in the concentrated washing liquid, which can be heated and dissolved in a water bath during dilution, and the results will not be affected during washing.

3. The sampler should be used at each step of sample addition, and the accuracy should be regularly checked to avoid test errors. It is best to control the sampling time within 5 minutes. If there are many specimens, it is recommended to use a volley gun to add samples.

4. Please make a standard curve at the same time of each measurement, it is best to make a double hole. If the content of the test substance in the specimen is too high (the OD value of the sample is greater than the OD value of the first well of the standard well), please first dilute it with a certain multiple (n times) of the sample diluent and then determine it. When calculating, please multiply the total dilution Multiple (× n × 5).

5. The sealing film is limited to one-time use to avoid cross-contamination.

6. Please keep the substrate away from light.

7. Strictly follow the instructions, and the test results must be determined by the microplate reader.

8. All samples, washing liquids and various wastes should be treated as infectious agents.

9. The components of different batches of this reagent shall not be mixed.

10. If there is any difference with the English manual, the English manual shall prevail.

Kit performance:

1. The correlation coefficient R between the linear regression of the sample and the expected concentration is above 0.95.

2. The batch and approval shall be less than 9% and 11% respectively

examination range:

100ng / L -2000ng / L

Calculation:

Taking the concentration of the standard as the abscissa and the OD value as the ordinate,

Draw a standard curve on coordinate paper, according to the OD of the sample

The value is determined by the standard curve; then multiplied by the dilution

Multiple; or calculate the standard using the concentration and OD value of the standard

The linear regression equation of the quasi-curve, the OD value of the sample

Substitute into the equation, calculate the sample concentration, and multiply by the dilution

The multiple is the actual concentration of the sample.

Storage conditions and validity period:

1. Store the kit: 2-8 ℃.

2. Validity: 6 months

Bulk Feed Truck

Bulk Feed Truck

Bulk feed truck, Bulk feed trucks, also known as bulk grain truck, Bulk corn truck,feed truck, Silo feed truck, Bulk Grain Carrier used to transport grains like corn, soy and concentrate for Animals Simple structure, reliable performance, easy to transport a large amount of control, maneuverability strong, non-polluting materials, which is widely used in feed for farmed transport major small and medium enterprises.

Bulk feed car Introduction

Mainly used for transporting bulk finished feed or feed produced from raw grain to livestock farms feed mills, poultry farms and feed processing user, but it can also be used to transport of certain non-corrosive powder granular materials, such as pharmaceutical powder and grain turnover .

Bulk feed feed tank car set up on the chassis of the truck, special facilities by the tank assembly, conveyor systems (horizontal discharge systems, vertical discharge system and the activities of the discharge system components), bulk feed tank cars hydraulic system (high-pressure pump the three output terminals via a line connecting the dispensing valve and the valve angle of the hydraulic motor, respectively, as well as lift cylinder series with horizontal discharge, vertical discharge, the discharge of the hydraulic motor activity), bulk feed tank cars electric systems, pneumatic warehouse mechanism and other components. At the bottom of the tank with a gate in the gate below the horizontal screw conveyor equipped (commonly known as horizontal stirring cage), is driven by the power take off from the auto gearbox output power, and then drive high pressure pump to drive the hydraulic system, hydraulic bulk feed tank cars motor gear driven by the level of the auger blade shaft and blade rotation, the activities of the delivery system (commonly known as activity stir cage) to feed output. Flat roof facing a discharge auger activity rotatably and lifting, transportation spiral lying in the top of the tank top; when unloading the lift, car bulk feed tank pipe end of the discharge port and livestock feed farm gate contact holding tank at the top of the alignment, complete discharge.

Bulk feed car Features

1 .. bulk transport of feed ratio packed into bags of transport not only labor-saving, and low cost.

2. Bulk feed tank body sealed in transport, reduce losses, quality assurance, to avoid contamination.

3. Automatic feeding on discharge, continuous operation, greatly improving production efficiency.

4. The sub-positions can be installed inside the tank, which can transport a variety of different types of feed or expanded media.

5. The standardization of components, easy maintenance.

Tank dimensions (L * W * H) and the corresponding volume of correspondence

Corresponds to the effective tank volume (m3) and the corresponding body size

Number of sub-tank positions 1-5 (with storage bodies, which can transport multiple types

The average discharge rate (kg / min) 510 (different drive forms will change accordingly)

Activities unloading system rotation angle of 180 degrees

Activities unloading system maximum elevation angle of 60 degrees

Transmission distance of maximum distance (m) 7.2

The maximum vertical distance (m) 8.2

Residual rate 0.01

Bulk feed Cars Category

Bulk feed car type vehicle and a separate tank (available appropriate trucks transport) and the like. Divided by driving form: electric discharge bulk feed truck, full hydraulic unloading bulk feed gas car unloading bulk feed car.

Bulk feed hydraulic car

Hydraulic feed bulk feed tank car set up on the chassis of the truck, special facilities by the tank assembly, conveyor systems (horizontal discharge systems, vertical discharge system and the activities of the discharge system components), the hydraulic system (high-pressure pump via a line three output terminals connected to the valve and dispensing valve are the corner of the hydraulic motor, and a horizontal lift cylinder discharge, vertical discharge, the discharge of the hydraulic motor activity), electric system, pneumatic storage bodies in series with the other components. At the bottom of the tank with a gate in the gate below the horizontal screw conveyor equipped (commonly known as horizontal stirring cage), is driven by the power take off from the auto gearbox output power, and then drive high pressure pump to drive the hydraulic system, the hydraulic motor via a transmission driven horizontal screw conveyor blade shaft and blade rotation, the activities of the delivery system (commonly known as activity stir cage) to feed output. Flat roof facing a discharge auger activity rotatably and lifting, transportation, spiral lying in the top of the tank top; when unloading the lift, the tube end of the discharge port and storage of livestock and poultry farms feed door contact tank top, aligned to complete discharge.

Unloading bulk feed gas car

Unloading of bulk feed gas car vehicle using a large flow of gas delivery technology, with low pressure, high flow, low noise, high output, transmission distance, discharge speed, low residual amount of material pollution. Widely used in various types of enterprises farming, feed processing enterprises feed transport, solve the problem of long-distance transmission can be realized without entering a vehicle that is able to complete the feeding step of feeding the tower, put an end to farm vehicles approach the most headaches prevention issues.

Auger bulk feed electric car

Electric auger bulk feed truck for different customers the latest development, new products to meet the low-end market, the car unworthy board generator, electric auger to use three-phase 380V mains supply, the wheels can adapt from the small rural country road. The car is very popular customers cost-effective for small road small farms, feed mills. Mechanical screw discharge mode, discharge speed, continuous operation, greatly improving production efficiency. It can be divided into two to four tank compartment while loading different feeds; simple components structure, convenient and flexible operation, easy maintenance.

Bulk Feed Truck,Bulk Feed Trailers,Feed Mixer Truck,Bulk Feed Discharge Truck

CLW GROUP TRUCK , https://www.clwgrouptruck.net