Paperback Filament Production Failure
2024-08-30 01:07:57
In the production process, paper binding must be piled up in different books. A sample book should be prepared on the basis of quality management. After signing the quality inspection personnel, the sample should be produced according to the sample. There are two aspects of quality control: one is the dataization and standardization of each process; the other is the management of process design and work flow. The former requires that all processes implement standardized operations, and the latter is the operational requirements for the formulation of work processes and processes.
In the production practice, 80% of quality accidents are caused by the lack of responsibility of the operators, and 20% are due to process reasons and materials. To make 80% of the accidents disappear in the bud, we must understand the technical requirements.
Failure in glue production
1) round back
The height of the book in the book clip and the signature of the book Qitai are too low, and the sign sticking out should be controlled at 11mm~12mm, and the position of the solid board should be improved; from the slotting knife is too high, the position of the cutter head should be reduced, and the signature is concave Groove depth is controlled within 1.0mm.
2) oblique book
The glue temperature is too high. When the book falls, the back of the book is not solidified and falls. The glue temperature is adjusted according to the paper and seasonal changes. Generally, the temperature is controlled between 160C and 180C. If the speed is too fast, the glue with a short curing time should be used, and the speed should be reduced. The opening of the book clip is too large, and the thickness of the book is 15mm. At the same time, the book aisle and the lever are narrowed.
3) The book's opening and notches are not rectangular
The degree of parallelism and verticality of the tray and the holder should be adjusted so that the backs of the book are aligned with each other.
4) The cover is bad
There is wild glue on the upper sealing roller, sticking to the cover of the book, and the bottom plate of the forming mechanism is viscose. The clamping plates on both sides are glued to seal the seal and seal the seal. Therefore, the residual glue is often removed and the methyl silicone oil is used to prevent the wild glue; The rubber on the wheel takes too long to produce wild glue. The glue application time should be fine-tuned. Try not to produce wild glue and minimize gum temperature.
5) The book cover is folded or misplaced
If the book position in the book clip is too high, the position of the tray must be raised. If the knife is too high, the position of the cutter head should be reduced. If the temperature of the glue is too low, the temperature of the glue should be increased. The glue stick should be left with glue. The glue stick should be adjusted. The gap between the plastic sheets is made zero, and the working status of the heating tube in the slush bar is checked; if the binding speed is too fast, the machine speed should be lowered and the drying time should be extended before cutting.
6) Leverage
The signature of the book is too low or the book position is low in the book clamp. The position of the solid board should be reduced. If the notch is too low, the position of the cutter head should be increased; the clamping force on the side of the bracket is too large and should be outward. Adjust the side clamp plate position properly.
7) Bubble or honeycomb film
The height of the book in the book clip and the height of the tray are too low. The position of the tray must be raised. The temperature of the backing glue is too low or the temperature of the glue stick is too low. After the measurement, the temperature is increased.
8) Back rip or over-squeeze
Low book position in the book clip, the position of the solid plate should be reduced; the pressure of the upper seal roller is too large, the clearance between the upper seal roller and the bottom of the book holder body is 9mm, the glue on the glue wheel is excessive, and the glue wheel and the scraper The gap of the board is adjusted to 0.2-0.5mm; the rubber wheel is too high and the pressure is too high, ensuring that the rubber wheel is in contact with the back of the book and can open the back of the book so that the glue penetrates into the book in a small amount.
9) Open or flanging the book in front of the book
The passivation of the milling cutter's cutting edge should sharpen the cutting edge and often remove the viscose. It is better not to use this machine for the return book processing. The adjustment of the milling backing support disc should be done properly.
10) Dispatch
Milling back depth is not enough; groove groove depth inappropriate, improper groove pitch, so that the depth of about 7.0mm, spacing between 5-10mm; hot melt adhesive temperature is too low, lack of fluidity and permeability, bonding is not strong , Should improve the glue temperature according to the paper; improper selection of hot melt glue, should choose the hot melt glue that is equivalent to the paper weight specification, save the high value of the coated paper book, avoid the use of hot melt glue process, use the first lock line After the way of gluing, prevent the spread of posts.
11) The middle part of the book is not even
When the book falls, the gap is too big, and a groove is made in the small board. When the glue temperature is too high, the book is not evenly thick and thin when it is glued. The groove is not clean, the paper hair is not removed, the adhesive cannot be leveled, and the milling and backing tool is not The sharpness, the angle of the blade is not correct, and the clearance between the blade and the plate is too large, which causes the back of the milling to be not smooth, and is not even after the glue is applied. The position of the solid plate is too low.
13) Wide Book Back
Slotted knife support plate is not aligned with the book clip; the upper seal roller is too high, forming excessive pressure on the back of the book; the rubber on the back rubber is too high, so that the glue penetrates between the pages; the book block is not loosely tied; the milling back is not Smooth, rough.
14) Wedge
The distance between the squeegee and the bottom surface of the book holder is too small, and the position of the sizing wheel should be reduced.
In the production practice, 80% of quality accidents are caused by the lack of responsibility of the operators, and 20% are due to process reasons and materials. To make 80% of the accidents disappear in the bud, we must understand the technical requirements.
Failure in glue production
1) round back
The height of the book in the book clip and the signature of the book Qitai are too low, and the sign sticking out should be controlled at 11mm~12mm, and the position of the solid board should be improved; from the slotting knife is too high, the position of the cutter head should be reduced, and the signature is concave Groove depth is controlled within 1.0mm.
2) oblique book
The glue temperature is too high. When the book falls, the back of the book is not solidified and falls. The glue temperature is adjusted according to the paper and seasonal changes. Generally, the temperature is controlled between 160C and 180C. If the speed is too fast, the glue with a short curing time should be used, and the speed should be reduced. The opening of the book clip is too large, and the thickness of the book is 15mm. At the same time, the book aisle and the lever are narrowed.
3) The book's opening and notches are not rectangular
The degree of parallelism and verticality of the tray and the holder should be adjusted so that the backs of the book are aligned with each other.
4) The cover is bad
There is wild glue on the upper sealing roller, sticking to the cover of the book, and the bottom plate of the forming mechanism is viscose. The clamping plates on both sides are glued to seal the seal and seal the seal. Therefore, the residual glue is often removed and the methyl silicone oil is used to prevent the wild glue; The rubber on the wheel takes too long to produce wild glue. The glue application time should be fine-tuned. Try not to produce wild glue and minimize gum temperature.
5) The book cover is folded or misplaced
If the book position in the book clip is too high, the position of the tray must be raised. If the knife is too high, the position of the cutter head should be reduced. If the temperature of the glue is too low, the temperature of the glue should be increased. The glue stick should be left with glue. The glue stick should be adjusted. The gap between the plastic sheets is made zero, and the working status of the heating tube in the slush bar is checked; if the binding speed is too fast, the machine speed should be lowered and the drying time should be extended before cutting.
6) Leverage
The signature of the book is too low or the book position is low in the book clamp. The position of the solid board should be reduced. If the notch is too low, the position of the cutter head should be increased; the clamping force on the side of the bracket is too large and should be outward. Adjust the side clamp plate position properly.
7) Bubble or honeycomb film
The height of the book in the book clip and the height of the tray are too low. The position of the tray must be raised. The temperature of the backing glue is too low or the temperature of the glue stick is too low. After the measurement, the temperature is increased.
8) Back rip or over-squeeze
Low book position in the book clip, the position of the solid plate should be reduced; the pressure of the upper seal roller is too large, the clearance between the upper seal roller and the bottom of the book holder body is 9mm, the glue on the glue wheel is excessive, and the glue wheel and the scraper The gap of the board is adjusted to 0.2-0.5mm; the rubber wheel is too high and the pressure is too high, ensuring that the rubber wheel is in contact with the back of the book and can open the back of the book so that the glue penetrates into the book in a small amount.
9) Open or flanging the book in front of the book
The passivation of the milling cutter's cutting edge should sharpen the cutting edge and often remove the viscose. It is better not to use this machine for the return book processing. The adjustment of the milling backing support disc should be done properly.
10) Dispatch
Milling back depth is not enough; groove groove depth inappropriate, improper groove pitch, so that the depth of about 7.0mm, spacing between 5-10mm; hot melt adhesive temperature is too low, lack of fluidity and permeability, bonding is not strong , Should improve the glue temperature according to the paper; improper selection of hot melt glue, should choose the hot melt glue that is equivalent to the paper weight specification, save the high value of the coated paper book, avoid the use of hot melt glue process, use the first lock line After the way of gluing, prevent the spread of posts.
11) The middle part of the book is not even
When the book falls, the gap is too big, and a groove is made in the small board. When the glue temperature is too high, the book is not evenly thick and thin when it is glued. The groove is not clean, the paper hair is not removed, the adhesive cannot be leveled, and the milling and backing tool is not The sharpness, the angle of the blade is not correct, and the clearance between the blade and the plate is too large, which causes the back of the milling to be not smooth, and is not even after the glue is applied. The position of the solid plate is too low.
13) Wide Book Back
Slotted knife support plate is not aligned with the book clip; the upper seal roller is too high, forming excessive pressure on the back of the book; the rubber on the back rubber is too high, so that the glue penetrates between the pages; the book block is not loosely tied; the milling back is not Smooth, rough.
14) Wedge
The distance between the squeegee and the bottom surface of the book holder is too small, and the position of the sizing wheel should be reduced.
Thermal transfer process printing method is divided into two major parts: transfer film printing and transfer processing, transfer film printing using dot printing (resolution up to 300 dpi), the pattern pre-printed on the surface of the film, the printed pattern layers are rich, bright colors, varied, small color difference, good reproducibility, can achieve the effect of the design pattern requirements, and suitable for mass production; transfer processing through the thermal transfer machine a processing ( Heating and pressure) will be transferred on the film of the transfer of exquisite patterns in the product surface, forming the ink layer and the product surface into one, realistic and beautiful, greatly improving the grade of the product.
Heat Press,Small Heat Press Machine,T Shirt Heat Press Machine,Ptfe Fiberglass Mesh Conveyor Belt
vchomy , https://www.vichenivchomy.com