Adjustment of saddle stitch stapler for post-press binding operation technique
(1) Adjustment of book delivery organization:
When transporting books of different specifications, in order to ensure that the book sending position is appropriate, the book sending position should be adjusted accordingly. The adjustment is very convenient, just manually turn the car, so that the connecting screw between the connecting block and the book-feeding connecting rod is at the adjustment hole on the rear guard of the machine, then loosen the screw to adjust the connection block and the book-feeding connecting rod The corresponding position between them can achieve the purpose of adjusting the book sending position. Tighten the screws when the book feeding position is proper.
(2) Adjustment of book collection agency:
During the collection process, the gap between the two collection wheels should be adjusted according to the thickness of the book. The gap is too large, and the book cannot be smoothly sent to the collection belt; the gap is too small, the book cannot pass the collection wheel or Crush the book. When adjusting, loosen the locking handle and pull the handle to adjust the spacing between the two rows of book-collecting wheels. Then lock it again; the correct position of the book-receiving wheel, book-receiving guide plate and book-receiving belt in the axial direction directly affects the neatness of book-receiving. When using the adjustment, make sure that the center of gravity of the book is in the middle of the book collecting wheel and the book receiving belt. Books of general specifications must be transported through the middle position of two pairs of book collection and two collection belts. Large-sized books are better transported by three to four pairs of collection wheels and three to four collection belts. The method of adjustment is very simple, as long as the jacking wires on the two parts of the book collecting wheel and the book guide plate are loosened, the book collecting wheel and the book guide plate can be moved arbitrarily in the axial position. wire.
(3) Adjustment of the tight hook mechanism:
According to the changes in the specifications of the bound book, the center of the two nail feet is required to be adjusted accordingly. When adjusting, loosen the lock nut, the bottom plate of the hook can move arbitrarily in the horizontal direction, and then lock the lock nut when it reaches the ideal state. In the vertical direction, if the clamping hook is raised too high, the book will be crushed; if it is raised too low, the bound book will not be secure. First overall adjustment: Loosen the nuts at both ends of the clamping hook push rod, and then turn the clamping hook push rod to adjust the position of the lifting frame, you can change the lifting height of the clamping hook claws, after reaching the requirements, then lock the two nuts if The height of each tightening claw is the same, and the adjustment is completed, otherwise, the adjustment is made separately: loosen the locking screw, rotate the adjusting screw, and the adjusting screw drives the lifting plate to change the height of the tightening claw.
In use, if there is a phenomenon that the iron wire is caught between the bottom plate of the tight hook and the claw of the tight hook, it can be removed by simply sliding the handle up and down twice.
(4) Adjustment of binding hands:
In order to adapt to binding various specifications of thickness and books, the binding hand needs to be adjusted. When the binding hand rises to the highest position, turn the M16 socket head cap screw on the binding hand. Turning counterclockwise, the binding hand is raised; turning clockwise, the binding hand falls. The indicator arrow is aligned with the value of the scale label on the binding hand, which is the thickness of the bound book.
(5) Adjustment of the binding head:
A: The adjustment of the unequal length of the two nail feet: When adjusting the unequal length of the two nail feet, first loosen the fastening screw and adjust the adjustable screw. If it is rotated clockwise, the left binding foot will be shortened; if it will be adjusted After the screw rotates counterclockwise, gently tap the U-shaped head to make the adjustable screw close to the head housing. At this time, the left nail foot will be lengthened. When the two nail feet are adjusted to the same length, the tightening screw will be locked. Just tight.
B: Adjusting the length of the wire feeder: According to the thickness of the book, the length of the wire feeder should be adjusted accordingly. During adjustment, loosen the nail screws and pull up the head cover to increase the length of the wire feed; push down the head cover to shorten the length of the wire feed.
Usage: Household, Washing Dish, Kitchen, Car,Bathroom, Pet and More.
Easy to make foam-with a little detergent he will produce a lot of foam.Bump design-anti-slip particles inside the glove.
Hook design-glove are easy to store and drain to avoid bacterial growth.High temperature resisitance-the glove are heat resistance to 220 degrees and can be sterilized by boiling water.
Silicone Gloves
Silicone Mitts,Silicone Oven Mitts,Silicone Oven Gloves,Silicone Cooking Gloves
YANGJIANG SHENGHAI INDUSTRIAL&TRADING CO., LTD , https://www.shenghaiyj.com