Promote PS Edition Industry Development (1)

In 2002, China's PS industry continued its rapid development. In the traditional PS version, there are roughly nine new lines under construction. Four of the production lines have already been put into production, and PS production, supply, and sales are still prosperous. Excellent situation. In the new CTP version, there are also many companies have given enough attention, some of them have already started or are planning to build a CTP plate production line.
The author summed up the development of the printing media as a list of the top ten information and personal opinions, and dedicated it to a wide range of readers.
I. On November 28, 2002, Beijing Zhaowei Technology Co., Ltd. Tianjin Branch held the second roll-to-roll production line for the continuous production line of the PS version. Its production line speed is 15m/min and is coated with a vacuum seal layer. At present, the domestic PS version exceeds supply, and the market competition is fierce, the company has made great efforts to open up the international market. In 2001, the output ranks sixth in the country, while the export ranks first in the industry, for our country to join After WTO, it has provided successful experience in exploring both domestic and international markets.
2. On March 13, 2002, Fuji Starlight Co., Ltd. held a conference for the publication of new technologies in Beijing. The company is a joint venture company jointly approved by the General Administration of Press and Publication and Japan Fujifilm Co., Ltd. and China Institute of Printing Science and Technology. With a total investment of 30 million U.S. dollars, the company is a combination of the advanced technology of the Starlight PS version of the China Institute of Printing Science and Technology and the advanced technology of the Fujitsu PS. It is reported that Fuji Starlight Company has completed the technological transformation of the original production line in 2002, and introduced a high-sensitivity, high-resolution and rough surface gas-guiding layer VPS-A type and a large development latitude. The PS versions of many new models, such as the P-1M and VP models, have been greatly welcomed by users. At present, the company is building a production line with a speed of 30 meters per minute. The production line will be put into production in 2003. The production line can produce CTP plates in addition to high-end PS plates. By then, the company will increase the total annual production by 10 million square meters. It is also known that the original PS version of the China Institute of Printing Science and Technology has undergone technological transformation and is mainly based on the small-offset PS printing version that is urgently needed by the market. Currently, the annual output of Xingguang brand small offset printing has exceeded 1 million square meters.
3. The CTP production line of the second film factory of Lucky Group was formally constructed on September 12, 2002 in Nanyang City, Henan Province. The plant tracked international advanced technology in the mid-1990s, successfully developed the CTP version with independent intellectual property rights, and after the trial production, the thermal CTP plate began preparations for a large-scale CTP production line. At present, the production line has been The country is listed as a "double high and excellent" project and is expected to produce at the end of this year. The output of the PS version of the plant increased from 4.52 million square meters in 1996 to 14.86 million square meters in 2001, with an average annual growth rate of 26.8%. The completion of the production line will increase the total annual production capacity of the second grade CTP and PS version by 1100. Ten thousand square meters.
4. The plate production base established by Kodak Poly Lighting Group (KPG) was held in Tianjin Economic Development Zone on July 8, 2002. The base is also the KPG's operation center in China, covering an area of ​​3,300. Square meters, is expected to put into operation in 2003. At that time, thermal-type CTP plates will be provided for the rapidly developing Chinese market.
V. The Longma Science and Technology Industrial Park, which was built by Zhangzhou Longma Aluminum Co., Ltd., was groundbreaking on December 26, 2002. According to the company's chairman Wang Xiaojun, the science and technology industrial park covers an area of ​​310 mu, with a total investment of 280 million yuan. The park includes Longma Aluminum Materials Co., Ltd. and Longma Materials Co., Ltd. Another three new projects were launched. One is a light steel structure plant with an annual output of 150,000 square meters. The second is the development of a computer direct imaging system and a high-speed PS plate production line. The third is an annual output of 50,000 tons of hot-rolled aluminum. , aluminum foil production line and color coated plate production line. It is expected that the park will take three years to complete. It shows that the park will develop towards the aluminum base and the printing plate association. (To be continued)