Plant Vitamin D (VD) ELISA Kit Instructions

The company specializes in supplying Elisa kits, quality assurance, price concessions, and can provide free testing services, please call to consult!

This kit can only be used for scientific research, not for medical diagnosis.

Quantitative detection kit for plant vitamin D (VD) (ELISA)

user's Guide

【Vitamin D (VD) ELISA kit kit name】

Quantitative detection kit for plant vitamin D (VD) (ELISA)

[Vitamin D (VD) ELISA kit kit use]

Quantitative detection of serum, plasma and related fluids.

【Principle of plant vitamin D (VD) ELISA kit detection】

This kit uses double-antibody two-step sandwich enzyme-linked immunosorbent assay (ELISA). Add the standard and the test sample to the pre-coated plant vitamin D (VD) monoclonal antibody transparent enzyme label coated plate. After incubation for a sufficient time, wash to remove unbound components, then add the enzyme label working solution After sufficient incubation time, washing to remove unbound components. Substrates A and B are added in sequence, and the substrate (TMB) is converted into a blue product catalyzed by horseradish peroxidase (HRP), which turns yellow under the action of an acid. VD) The concentration is positively correlated. The OD value is measured at a wavelength of 450 nm. Based on the OD value of the standard and the sample, the content of plant vitamin D (VD) in the sample is calculated.

[Vitamin D (VD) ELISA kit composition]

1

Enzyme coated plate

12 holes × 8

7

Developer A liquid

6mL

2

Standard

0.3mL × 6 tubes

8

Developer B liquid

6mL

3

20 times concentrated washing liquid

25mL

9

Stop solution

6mL

4

Sample diluent

6mL

10

Instructions

1 serving

5

Special diluent

6mL

11

Sealing film

2 sheets

6

Enzyme reagent

6mL

12

sealed bag

1

[Reagents and equipment not required by the plant vitamin D (VD) ELISA kit]

1. 37 ℃ thermostat

2. Standard specification microplate reader

3. Precision pipettes and disposable tips

4. Distilled water

5. Disposable test tubes

6. Absorbent paper

【Steps of Plant Vitamin D (VD) ELISA Kit】

1. Preparation: Remove the reagent kit from the refrigerator and re-equilibrate at room temperature for 30 minutes.

2. Mixing solution: dilute the 20-fold concentrated washing solution with distilled water to the original one.

3. Add standard products and samples to be tested: take a sufficient number of enzyme-coated plates and fix them to the frame. Set up standard wells, sample wells to be tested and blank control wells, record the positions of each well in the standard wells. Add 50μL of standard product; first add 10μL of sample to be tested, and then add 40μL of sample diluent (that is, the sample is diluted 5 times); blank control well is not added.

4. Incubation: Incubate in a 37 ° C water bath or thermostat for 30 minutes.

5. Wash the plate: discard the liquid, pat dry on the absorbent paper, fill each hole with the washing solution, let stand for 1min, shake off the washing solution, pat dry on the absorbent paper, repeat the washing 4 times (you can also use the washing machine to press Instructions for washing the board).

6. Add enzyme-labeled working solution: add 50μL of enzyme-labeled working solution to each well, without adding blank control wells.

7. Incubation: Incubate in a 37 ° C water bath or thermostat for 30 minutes.

8. Wash the plate: discard the liquid, pat dry on the absorbent paper, fill each hole with washing liquid, let stand for 1min, shake off the washing liquid, pat dry on the absorbent paper, repeat the plate washing 4 times (you can also use the washing machine to press Instructions for washing the board).

9. Color development: add 50μL of developer A solution to each well, and then add 50μL of developer B solution, mix for 30s with a plate mixer (or gently shake for 30s by hand), and avoid color development at 37 ℃ for 15min .

10. Termination: Remove the enzyme labeling plate and add 50μL of stop solution to each well to stop the reaction (the color changes from blue to yellow)

11. Determination: Zero the blank holes, and within 15 minutes after termination, measure the absorbance (OD value) of each well with a wavelength of 450 nm.

12. Calculation: According to the concentration of the standard product and the corresponding OD value, calculate the linear regression equation of the standard curve, and then calculate the corresponding sample concentration on the regression equation according to the OD value of the sample. You can also use various application software to Calculation. The final concentration is the actual measured concentration times the dilution factor.

[Vitamin D (VD) ELISA kit sample requirements]

1. The sample cannot contain sodium azide (NaN3) because sodium azide (NaN3) is an inhibitor of horseradish peroxidase (HRP).

2. The specimen should be extracted as soon as possible after collection. The extraction should be carried out according to relevant literature. If the test cannot be performed immediately, the specimen can be stored at -20 ℃, but repeated freezing and thawing should be avoided.

3. The sample should be fully centrifuged, without hemolysis and particles.

【Notes on Plant Vitamin D (VD) ELISA Kit】

1. The experiment is carried out in strict accordance with the instructions, and the result of the experiment must be determined by the reading of the microplate reader.

2. If the enzyme-labeled coated board is not used up after opening, it should be put into a sealed bag and added with desiccant immediately.

3. It is recommended that all standards, samples and blank controls be tested in duplicate, and the average value is taken to reduce the experimental error.

4. Keep in mind that the sample has been diluted 5 times. The calculation result is multiplied by 5 to obtain the actual concentration of the sample.

5. The quantitative range of this kit is 6.25-200ng / L. If it exceeds this range, it is calculated from the extension of the standard curve. It is not used for accurate quantitative results. ), Multiplied by the total dilution factor is the final concentration of the sample.

6. If the color is too light, the substrate incubation time can be extended properly.

7. In order to avoid cross-contamination, the tips, samples and blank controls should be replaced with a new one for each addition; the common components such as enzyme working solution, sample diluent and substrate should be cantilevered, and they should not touch the microwells. ; Do not reuse the sealing film.

8. The kits are used within the warranty period, and different batches of reagents should not be mixed.

9. Substrate B is sensitive to light and avoid prolonged exposure to light.

[Summary of operating procedures of plant vitamin D (VD) ELISA kit]

Prepare reagents, samples and standards

Add prepared samples and standards, and react at 37 ℃ for 30 minutes

Wash the plate 4 times, add the enzyme reagent, and react at 37 ℃ for 30 minutes

Wash the plate 4 times, add color developing solutions A and B, and develop at 37 ℃ for 15 minutes

Add stop solution

Read OD value within 15 minutes

Calculation

【Detection range of plant vitamin D (VD) ELISA kit】

Please inquire

【Specification of Plant Vitamin D (VD) ELISA Kit】

96 servings / box 48 servings / box

【Storage of Plant Vitamin D (VD) ELISA Kit】

Store at 2-8 ℃, protected from light and moisture.

【Validity of Plant Vitamin D (VD) ELISA Kit】

6 months

Stainless Steel Sculpture

Stainless steel large sculpture now basically occupies the mainstream, because stainless steel material has good characteristics, has been recognized by most of the urban landscape, but also has become an indispensable scenery inside the sculpture. Now there are different materials of sculpture, stone carving, copper carving, stainless Steel Sculpture, glass steel sculpture, weathering steel sculpture, but with some high-grade environment and setting, are the main choice of stainless steel sculpture material! Stainless steel sculpture material has good corrosion resistance, not afraid of air water. Steam, as well as the wind and sun environment, which is also a very important factor of stainless steel sculpture. Second, the color of stainless steel sculpture is also relatively fresh, but also according to the demand of spraying, modeling out of a more advanced and better sense of art, for the environment and the city will increase beautiful scenery.

Name Decorative Stainless Steel Sculptures
Material Stainless steel
Size Customized
Weight 100KG
Packing wooden

Stainless Steel Sculpture




Stainless Steel Sculpture

Stainless Steel Sculpture

Stainless Steel SculptureStainless Steel Sculpture103

Packing

Packing will by pallet/carton/ wooden box,according to different demand.


sculpture packing Jpg

sculpture packing


Stainless Steel Sculpture Stainless Steel Sculpture,Stainless Steel Artwork,Stainless Steel Statue,Stainless Steel Yard Art

Henan Jinbailai Industrial Co.,Ltd , https://www.gardensteelarts.com