Picture book edition paper method

For manufacturers who use manual folding and binding, whether the operation is accurate, standardized, or even the folding method is an important factor in ensuring the quality of books and magazines. However, what can't be ignored is whether the accuracy of the layout table paper is also an important factor directly affecting the quality of the product.

According to my work practice, I summarized a method of painting and publishing desk papers. After mastering and mastering the points, the table papers I drew were printed on the 64-page open book paper on the web as an example: the general error is less than 0.3mm (error within and outside the line drawn by a 0.2mm marker). Presented to colleagues, interested parties may wish to try.

1. Necessary tools

(1) It is larger than folio wood drawing board (preferably made into cassette type, and can store paper inside to ensure that the paper is flat and can hold some drawing tools).

(2) Number 2 sewing needles, needle nose removed, spare. It is best not to use a pin, because the uneven thickness is easy to bend, affecting the accuracy of the table paper.

(3) One pin hammer hard object.

(4) Zha Kong uses a drawing needle.

(5) Compass, crayons, rulers and other necessary tools.

2. Making points

When drawing table paper, use the vertical line as the starting reference line, and take one point up and down, first measure the size of the left and right side of the table paper, and then use the steel needle to make a note at the desired drawing line. After the amount is finished, lightly press the sewing needle into the small hole of the note and put the ruler against the needle. After drawing on one side, flip the drawing board and draw the other side in the same way. If yes: Take the horizontal center line as the starting reference line, arbitrarily select one point from the left and right, measure the size and pin, and draw the connection line between the upper and lower centerline respectively.

At this point, a complete and accurate booklet is completed.

3. Precautions

(1) When drawing the table paper, take the vertical line of the middle point as the standard, use the first 50cm of the rule to measure the size of one side, make a note and staple, and then use the full length of the ruler to draw the line. Similarly, flip the drawing board and use the first 50cm of the ruler to record another size, write a needle, and draw a line. In this way, small errors in the ruler can be avoided, and the right and left sides of the drawn table paper can be completely matched with each other to achieve accurate overprinting. Can not cut the size of a full-length ruler once measured, because the general length of 100cm plastic ruler 0-50cm, 50-100cm are also 50cm in length but before and after marking in mm units, compared to some errors.

(2) When the hole is recorded, the hole should not be too big or too deep. It is better to use a smaller needle than the diameter of the needle. In this way, the set needles are easy to be vertical and consistent in depth and depth, and the drawn table paper is accurate.

(3) When drawing a line, the ruler should rest on the outer side of the nail. After drawing one side of the table paper, the other foot is also the same (using the starting line of the midpoint as a standard) to rest on the outside of the needle. The ruler is on the outside of the needle, while the other ruler draws on the inside.

(4) The ruler's ruler should be widened by a certain ruler. The plastic ruler should not be too narrow. If it is too narrow, the ruler's pushing will easily affect the accuracy of the table paper due to the hand pushing.

(5) The paper on the book-drawing table paper should be thicker, so that once the wrong line is drawn, the tape can be used to tear off the wrong line, but the paper is not easy to break, and it is easy to save.

(6) The pen on the drawbench paper is best drawn with two different colored markers or pens to draw the incision line, the finished product line, and the plated heart line. Together with the labeling method, the thickness of the spine, the width of the head, the foot of the ground, the size of the heart, and so on. Intuitive and intuitive, it is not easy to make mistakes when making impositions. When you get a job again, you can usually find a suitable retention table paper after you read the production worksheet. You do not need to draw the table paper every time you live.

(7) The ruler of the paperback should not be used in conjunction with the cutting ruler. Cutting film is used more often than the ruler. The ruler will be scratched and the accuracy of the table paper will be affected.

I believe that the above method of drawing table paper, after mastery of skill, has high precision, and there is almost no error in overprinting. It is better than drawing one side first, and then folding the other side after half folding. There are deficiencies, sincerely hope that the industry Tongren Yazheng