Working principle of human prostaglandin E2 (PGE2) ELISA kit
Working principle of human prostaglandin E2 (PGE2) ELISA kit
English name: Human Prostaglandin E2, PG-E2 ELISAKit
Experimental principle:
This kit uses the double antibody sandwich method to determine the level of human prostaglandin E2 (PGE2) in the specimen. The microplate was coated with purified human prostaglandin E2 (PGE2) antibody to prepare a solid-phase antibody. Prostaglandin E2 (PGE2) was added to the monoclonal antibody-coated microwells in turn, followed by HRP-labeled prostaglandin E2 (PGE2) ) The antibody binds to form an antibody-antigen-enzyme-labeled antibody complex. After thorough washing, the substrate TMB is added for color development. TMB is converted into blue under the catalysis of HRP enzyme, and into the final yellow under the action of acid. The color depth is positively correlated with prostaglandin E2 (PGE2) in the sample. The absorbance (OD value) was measured with a microplate reader at a wavelength of 450 nm, and the level of human prostaglandin E2 (PGE2) in the sample was calculated by a standard curve.
Steps
1. Dilution and loading of standard products: set 10 standard wells on the enzyme-coated plate, add 100 μl of standard products in the first and second wells, and then add standard products in the first and second wells 50μl of diluent, mix well; then take 100μl from the first well and the second well and add them to the third and fourth wells respectively, and then add 50μl of standard diluent to the third and fourth wells respectively, mix well; Then take 50μl each in the third and fourth wells and discard it, then add 50μl each to the fifth and sixth wells, and then add 50ul of the standard dilution solution to the fifth and sixth wells respectively, and mix well; After mixing, take 50μl from the fifth and sixth wells and add them to the seventh and eighth wells respectively. Then add 50μl of the standard dilution solution to the seventh and eighth wells respectively. Take 50μl from the eight wells and add them to the ninth and tenth wells. Then add 50μl of the standard dilution solution to the ninth and tenth wells. After mixing, take 50μl from the ninth and tenth wells and discard. (After dilution, the volume of each well is 50μl, and the concentrations are 180U / mL, 120U / mL, 60U / mL, 30U / mL, 15U / mL).
2. Add samples: set up blank wells (the blank control wells do not add samples and enzyme reagents, the rest of the steps are the same) and the sample wells to be tested. Add 40μl of sample diluent to the test sample well of the enzyme-coated plate, and then add 10μl of the sample to be tested (the final dilution of the sample is 5 times). Add the sample and add the sample to the bottom of the well of the microplate, try not to touch the wall of the well, shake gently to mix.
3. Incubation: Seal the plate with a sealing plate and incubate at 37 ° C for 30 minutes.
4. Mixing solution: Dilute 30 times (20 times of 48T) concentrated washing liquid with distilled water 30 times (20 times of 48T) and then use.
5. Washing: Carefully peel off the sealing film, discard the liquid, spin dry, fill each well with the washing liquid, let it stand for 30 seconds and then discard, repeat this 5 times, pat dry.
6. Add enzyme: add 50μl of enzyme label reagent to each well, except blank well.
7. Incubation: The operation is the same as 3.
8. Washing: The operation is the same as 5.
9. Color development: add 50μl of developer A to each well, then add 50μl of developer B, mix gently, and develop at 37 ° C in the dark for 15 minutes.
10. Termination: Add 50μl of stop solution to each well to stop the reaction (at this time the blue will turn to yellow).
11. Determination: Measure the absorbance (OD value) of each well in sequence with the blank air conditioner at zero and 450 nm wavelength. The measurement should be carried out within 15 minutes after adding the stop solution.
Precautions:
1. The kit should be equilibrated at room temperature for 15-30 minutes before being taken out of the refrigerated environment. If the enzyme label coated plate is unopened, the strip should be stored in a sealed bag.
2. Crystals may be precipitated in the concentrated washing liquid, which can be heated and dissolved in a water bath during dilution, and the results will not be affected during washing.
3. The sampler should be used at each step of sample addition, and the accuracy should be regularly checked to avoid test errors. It is best to control the sampling time within 5 minutes. If there are many specimens, it is recommended to use a volley gun to add samples.
4. Please make a standard curve at the same time of each measurement, it is best to make a double hole. If the content of the test substance in the specimen is too high (the OD value of the sample is greater than the OD value of the first well of the standard well), please first dilute it with a certain multiple (n times) of the sample diluent and then determine it. When calculating, please multiply the total dilution Multiple (× n × 5).
5. The sealing film is limited to one-time use to avoid cross-contamination.
6. Please keep the substrate away from light.
7. Strictly follow the instructions, and the test results must be determined by the microplate reader.
8. All samples, washing liquids and various wastes should be treated as infectious agents.
9. The components of different batches of this reagent shall not be mixed.
10. If there is any difference with the English manual, the English manual shall prevail.
Calculation:
Taking the concentration of the standard as the abscissa and the OD value as the ordinate,
Draw a standard curve on coordinate paper, according to the OD of the sample
The value is determined by the standard curve; then multiplied by the dilution
Multiple; or calculate the standard using the concentration and OD value of the standard
The linear regression equation of the quasi-curve, the OD value of the sample
Substitute into the equation, calculate the sample concentration, and multiply by the dilution
The multiple is the actual concentration of the sample.
(This picture is for reference only
Kit composition:
Kit composition
48 hole configuration
96-well configuration
save
Instructions
1 serving
1 serving
Sealing film
2 pieces (48)
2 pieces (96)
sealed bag
1
1
Enzyme coated plate
1 × 48
1 × 96
Store at 2-8 ℃
Standard product: 270U / mL
0.5ml × 1 bottle
0.5ml × 1 bottle
Store at 2-8 ℃
Standard dilution
1.5ml × 1 bottle
1.5ml × 1 bottle
Store at 2-8 ℃
Enzyme reagent
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Sample diluent
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Developer A liquid
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Developer B liquid
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Stop solution
3ml × 1 bottle
6ml × 1 bottle
Store at 2-8 ℃
Concentrated washing liquid
(20ml × 20 times) × 1 bottle
(20ml × 30 times) × 1 bottle
Store at 2-8 ℃
Storage conditions and validity period:
1. Store the kit: 2-8 ℃.
2. Validity: 6 months
With the development of science and technology in daily life, technology has made a lot of things very convenient. People rarely need an axe in their daily life. The axe gives people the feeling that it is a tool for cutting wood and defending themselves. But sometimes the function of an axe can not be replaced by other things. Next, let's learn about the knowledge related to multi-functional axes!
The multi-functional axe is a multi-functional rescue hand tool, a portable hand tool integrating the functions of spade, axe, hammer, pry, saw, etc. It is a good rescue helper carried by the military, armed police, fire fighting, disaster relief and rescue personnel. It can carry out rescue work in various special occasions such as fire scene, disaster scene (broken doors, windows, plates and earthquake, collapse, vehicle and other accidents), and can well solve various rescue problems. It is one of the demolition and rescue tools for rescue and relief, and also an essential tool for survival in field activities.
Features of multi-function axe:
1. The multi-function axe is a portable multi-function hand tool It is a multi-functional hand tool integrating axe, pliers, knife and abrasive tools.
2. The full set of tools are packed with a special tool kit (flame retardant material), which can be buckled on the belt and carried with you. It is very convenient to use.
3. The whole set of products are designed with ergonomics, and the structure is compact and reasonable; According to the different occasions of using the tools, select various high-quality steel materials matching them to meet the use effect.
4. Multi functional hand tool, with detachable function, the whole set of tools only share one main handle, and the only handle is used together with other tool heads.
5. The whole set of tools are mostly machined, with high surface roughness, good matching performance, flexible and convenient use, and beautiful appearance.
Camping Supplies,Camping Gear,Camping Tools,Wilderness Tools,Field Tools
OYEAL Global , https://www.oyealhome.com